Showcase Thread

[Skorpio]

Hmm, Gryphon could be a nice name... and that's not used in the Battletech universe so far AFAIK.

But there's a Griffin. http://www.mechground.com/index.php?opt ... temid=2071

[qubodup]

Blade Eagle

[charlie]

Linwarrio3D needs some better models.

[Julius]

Well to be honest LinWarrior needs better art in any sense... I wouldn't even know where to start with that game. Ideally I would like to integrate this model into ZeroBallistics however... Tanks VS. Mechs sounds like a lot of fun

[Sindwiller]

Meh. It lacks some additional antennae and stuff.

[Julius]

Hmm Blade Eagle... sounds too American I think I will stick with Gryphon... "MCU-43-Gryphon" or something like that.

ahh btw... still unsure about the arms/weapons:


Do you like this mini-gun design?

[qubodup]

"MCU-43-Gryphon"

Sounds too mythological. In any case there should be no dash before the non-serial-number-ish name ("MCU-43 Gryphon")

ahh btw... still unsure about the arms/weapons:


Do you like this mini-gun design?

The mini-gun looks weird, I get the feeling the mech is very small because of it (I'm used to man-held miniguns from games) a projectile arm should look like a tank gun. The arms could be made of less specific weapon design, so it can be flexible without having to re-model the arms. Basically I mean that the weapons should be covered (heat-sinks/armor can be used as an explanation here).

[Julius]

Yes, I am aiming for a slightly modular design, but since I want to leave the arms as a separate mesh for animation purposes (and destruction model parts) anyway, I guess you should just replace the entire arm when going for a different weapon design.

The smallness however is actually intended... well maybe not as small as "hand-held" but like those build in miniguns of a attack helicopter. This isn't really ment to be a huge house high mech, but something similar to the size of a tank (but taller of course).

Maybe I can make it look a bit more massive, by adding more (and then smaller) barrels to the mini-gun?

[qubodup]

Maybe I can make it look a bit more massive, by adding more (and then smaller) barrels to the mini-gun?

Maybe two more barrels (6 in total?) but actually I think that would make it seem more fragile.

I think the barrel end is a little to long. [ref]

PTPC0.jpg (9.99 KiB) Viewed 142794 times

Also a flash suppressor might make it look more massive. [ref1] [ref2]

[Julius]

Better?

I don't like the idea of the flash suppressor however.

But I will probably have a break modeling it now... as it starts to look strange to me, which is usually a good sign that I should let it be for a week or two. Anyone want the model as it is already?

[qubodup]

I like it better!

I think you should put it on oga now

[Julius]

http://opengameart.org/content/mcu-43-gryphon-mech

Also broadened the center piece a bit... unsure if I should revert back to how it was. For sure looks more massive now

[qubodup]

http://opengameart.org/content/mcu-43-gryphon-mech

Also broadened the center piece a bit... unsure if I should revert back to how it was. For sure looks more massive now

looks better IMHO

[Julius]

http://i.imgur.com/KBove.png (old picture)

Doodleing around with another mech model... I am trying to go for a somewhat unique design (harder than you would think... everything has been done already ), which doesn't screem Battletech (or Gundam, or HeavyGear etc.).

Is supposed to be a lightweight, small urban-fighting mech... almost power-armor size wise (e.g. 4m or so tall).

Suggestions are welcome, also in regard to the uniqueness (e.g. do you think it looks like something you have seen before?).

Edit: small update:

[Julius]

Another update

[Julius]

I guess the sketch is done... for today at least

Lets see if I find the motivation to work on it tomorrow some more

I think it would be cool if I could make a full set with different weapon loadouts and a high poly version for normalmaps... but I am really lazy

Attached you can find the obj (exported from Wings3d btw). License as usual GPL (any version) or CC-By-SA. But as this is a work in progress I guess there is not much point in useing it yet

[Skorpio]

That's a very nice design. Reminds me of ... no existing mech! Must be a new machine. I really like the thin look, only the feet seem to be a bit too thin.

[charlie]

Julius, please do more work on it, it looks great. The plates on the shoulders look like effective armour. You should at least get some animations done and get it rigged so it can be used by LinWarrior.

[hc]

Uh oh, really need an tech/integration FAQ.
Rigging and animations are *NOT* necessary for LinWarrior - not even texturing:
+ Rigging needs to be re-done currently anyways in MisfitModel 3D with special joint names
+ Animation is done live in-game procedurally using the special joint names (LW had this way before spore
+ Texturing is done using solid texturing (like carved from the full material) automatically x,y,z model coord transforms to u,v,w tex coord. (to be enhanced eventually by custom detail texturing)

What's necessary for a LinWarrior integration is publishing the model to OGA, as WIP is just fine (or blendswap if you insist).
That's integration policy

BTW: Nice model!

[Julius]

another update... started preparing the mesh for seperation into seperate mechanical easy to animate parts.

[Julius]

Am I the only one posting in this thread?

Experimenting with a sort of TF2 inspired stylized anatomy... for the face I am thinking about using a animated texture to be able to make all sort of bad internet jokes (smilely faces etc)

[qubodup]

I'm at BIGJam 2011 and today's theme was "zero gravity acrobats".


http://opengameart.org/content/sphere-objects

[charlie]

Thought this was pretty cool and just dying to be added to a Free software 3D space game:
http://www.blendswap.com/3D-models/vehi ... yard-v0-6/

[Julius]

Yeah those are cool (but sadly not UV mapped and textured), but why did you change the title of the entire thread?

[charlie]

I didn't, qubodup did probably by accident when merging the thread. Oopsie!

EDIT: fixed!